Hello to everyone, I took my tranny down from the x5 is, due to jolt gears when hot!, and i am about to order the rebuild kit for it,i. ZF 5HP24 Custom Rebuild Bundle. This Will Include Every Possible Item Needed to Correctly Rebuild and Update Your Transmission. Input Clutch Drum. Find great deals for 5hp24 AUDI BMW VOLKSWAGEN PASSAT Transmission Rebuild Overhaul Kit TA. Shop with confidence on eBay!.
|Published (Last):||25 September 2010|
|PDF File Size:||6.83 Mb|
|ePub File Size:||5.89 Mb|
|Price:||Free* [*Free Regsitration Required]|
It’d be really good to make a section on the site for Auto Trans rebuilds, and really get the knowledge out there for all those with the time to fix dodgey trans behaviours. Other one as for the overdrive rear box that needs to come out also? The time now is The technician replaced the drum with the updated part only to have it come back with the same complaint and the same broken drum.
If not enough clearance, remove transmission and check to see if converter is seated in front pump properly.
Transmission Rebuilding ZF 5HP24 (advice need it) –
The torque converter if i put with face down in some to drain the oil,that should be fine? Wasn’t in a hurry as it really is our winter driver.
The most complex part was removal and re-installation from the car, made more difficult as I was: Notes rebkild a recent transmission rebuild ZF 5HP Find all posts by plums.
There is an updated pressure regulator valve See Figure 2 which could help the situation as long as the valve bore is not worn. I think you made the right call on tearing it down, and it sounds like your problems are over. The VB can easily be removed once the pan is off the tranny and once benched the process to replace VB components is straightforward. I was unsure if the ‘F’ valve mentioned in the parts referred to this valve issue.
Notes from a recent transmission rebuild (ZF 5HP24)
I’ve built a lessons learned doc for some other forum members which I’d be happy to forward on to anyone contemplating doing a rebuild. Sorry – rebui,d just now I did a quick google search on “5hp24 rebuild” and there looks like there are some good ones out there.
All the cooling stuff. If its too big, I’ll break it into smaller chunks. Curious because I forgot the first time and the first few shifts resulted in a horrible “squak” as the trans. Thank you for the help.
rebuiild Perhaps this forum can help. I did not think the TC installation was as big a deal as I now read. D Have only taken one apart to see where it failed.
If it was, how did you deal with the valve body wear? The car has done 7, miles 11, km since the rebuild, with no subsequent issues.
5hp24 AUDI BMW VOLKSWAGEN PASSAT Transmission Rebuild Overhaul Kit T13202A
Sounds like the end result was as good as or better than a rebuild from all but the best shops. My old engine from my iL has a spun rod bearing. Did you have to go rsbuild into it for any “seconds” afterward? BB code is On. I have not done the bottom end before. I took my time and rebuilt it over many weekend over the summer. Later today I’ll 5h2p4 at uploading it.
I have read of some completing the repair without doing a complete tear down and re-assembly. In my case, I ordered the upgraded piston on spec as I was doing the rebuild, but it was missed on the order.
Thank you for any help. The F drum houses a clutch in the transmission, so no relation to the piston in question. Bosanci – East coast supplier, but good peeps OK, end float, I found this so I know what you are talking about. Will you start tear down with valve body first or the 5hp224 part from the TC side?
Alsoi see some people talking about a manual,is that the zf 5hp24 repair manual? I figured I could always do that from under the car without having to pull the tranny.
ANy questions drop me a line. All was well after a few times but definately an “Oh, no” moment. Same search today shows lot of vendors with rebuilt units at good prices. Ed, did you soak the clutches in ATF?
The transmission shifts as always and the new Torque Converter appears to have cured the driveline vibration as well as occasional harsh downshifts I think 5gp24 caused by the lock up clutch in the TC failing to release. Posting Quick Reply – Please Wait. Actually I didnt mean that end float: No more practice please, I like doing things like this one time, the second time it becomes “work”. Find all posts by Boomer from Boston.