74LS164 DATASHEET PDF

Part Number: 74LS, Maunfacturer: Motorola, Part Family: 74, File type: PDF, Document: Datasheet – semiconductor. These 8-bit shift registers feature gated serial inputs and an asynchronous clear. A low logic level at either input inhibits entry of the new data, and resets the first. This 8-bit shift register features gated serial inputs and an asynchronous reset. The gated serial inputs (A and B) permit complete control over incoming data as a.

Author: Dohn Samukasa
Country: Malta
Language: English (Spanish)
Genre: Sex
Published (Last): 22 May 2016
Pages: 102
PDF File Size: 18.56 Mb
ePub File Size: 14.60 Mb
ISBN: 246-4-39118-477-4
Downloads: 90400
Price: Free* [*Free Regsitration Required]
Uploader: Maugor

So, my next iteration of this thing is definitely going the pull-UP route. Low Level Input Voltage. I am a complete beginner, so please excuse any incredibly stupid mistakes i made! Functional operation should be restricted to the Recommended Operating Conditions. You could add 2 or 3, 22nF’s in place of the nF. The IC is a shift register so it does datahseet have a latch function, any data in the SR is stored until the power is removed or its clocked out Hence, the datasjeet of my second IV would be high all the time thanks to the soon-to-be soldered pull-up.

Fully Buffered Clock and Serial Inputs. Data at the serial inputs may 74lw164 changed while the clock is high or low, but only information meeting the setup requirements will be entered clocking occurs or the low-to-high level transition of the clock input. Read the above entry d it seems that the LS type ICs are famous for their floating voltages and sensitivity – is there some other type of IC that might be more forgiving for a beginner?

Fully Buffered Clock and Serial Inputs. Propagation Delay Time, Clock to Q. The LED are using a Ohm resistor thats what an online calculator recommended. Low Level Input Voltage. If I have a shared clock signal for both the ICs which seems to be datashet common praticeAs stated when inputs are connected to datashest pins, NO pull ups.

  E W BULLINGER NUMBER IN SCRIPTURE PDF

Diver Well-Known Member Nov 16, Thread starter 744ls164 Start date Nov 16, Data at the serial inputs may be changed while the clock is high or low, but only information meeting the setup requirements will be entered clocking occurs or the low-to-high level transition of the clock input.

Now that that’s cleared up: When I switch on the lights in my house, this often triggers the signals. Setup Time, A1 or A2 to Clock. Didn’t help at all. High Level Input Current.

But I’d be happy to stand corrected. That’s why am a bit mad at me for getting stuck so early on! Thank you very much for that diagram – although I think I have none of the components you added at 74ls146 and I hope they sell them here!

74LS164 8-bit Shift Register IC

You must log in or register to reply here. The 22nF are for the switch contacts, to eliminate any electrical noise, caused by switch dwtasheet bounce. Or am I mistaken about the meaning of ‘Low’ and ‘High’?

All inputs are diode- clamped to minimize transmission-line effects.

The gated serial inputs A and B permit complete control over incoming data as a low at either or both input s inhibits entry of the new data and resets the first flip flop to the low level at the next datassheet pulse. Output Short Circuit Current.

Maximum Ratings are those values beyond which damage to the device may occur. High Level Output Current. Or am i maybe measuring the voltage in a wrong way?

  EJB KATHY SIERRA PDF

If you just ‘hook things up’ as the ‘so call experts’ state you will get the problems that you are experiencing. You can see a photo of my circuit dwtasheet I hacked together according to various pretty pictures I found online here: This doesn’t seem very desirable to me?

74LS 데이터시트(PDF) – System Logic Semiconductor

A high level input enables the other input which will then determine the state of the first flip-flop. High Level Output Voltage. I was just reading up on pull-ups, etc. I already had the circuit soldered, and being the stubborn guy i am and because of my lack of solder-removal-wickI tried it with pull-down resistors 1k to GNDagainst all recommendations i read online.

Could I simply buy a handful of the same ones, or does the difference actually make a huge difference, somehow? Hence, the input of my second IV would be high all the time thanks to the soon-to-be soldered pull-up.

All diodes are 1N or 1N I also posted this question over at Electronic Circuits on Discovercircuits. The output pin can sink or source current, check the datasheet for your IC type. The IC is very fast so you will [ or shouldn’t] see any flicker as the SR clocks.

A high level input enables the other input which will then determine the state of the first flip-flop. Thank you two for the quick reply. Propagation Delay Time, Reset to Q. That switch does NOT turn on the outputs – but touching that pin dataheet. Search field Part name Part description.